Using Category 1 and 2 Equipment With the Same Quick Hitch (2024)

Feb 4, 2014 / Using Category 1 and 2 Equipment With the Same Quick Hitch

#1

T

trook

Gold Member
Joined
Oct 21, 2007
Messages
455
Location
North Central Mississippi
Tractor
JD 5075E Cab

    Tomorrow, I intend on purchasing a JD 5075E cab with a MX-8 rotary cutter. I already have several category 1 attachments such as a disk, fertilizer spreader and box blade that are equipped with the collars to accept the category 1 JD I-match quick hitch (from my previous tractor) that I will be using with this new tractor.

    The MX-8, as I understand it, is category 2 and will not work with the category 1 quick hitch that I intend to purchase with this new tractor. Obviously, I do not want to purchase both cat 1 and cat 2 JD quick hitches. I anticipate that the MX-8 will be used much more than all other attachments, but I would certainly like the ability to attach and detach the MX-8 with ease.

    What is the best solution here to be able to utilize my current cat 1 attachments with a quick hitch while still being able to use a quick hitch with the MX-8? Will I have to remove the cat 1 quick hitch every time I want to attach the MX-8 or can I somehow make these compatible? Is there a way to use a category 2 quick hitch with my current attachments (I'm not aware of this)?

    Feb 4, 2014 / Using Category 1 and 2 Equipment With the Same Quick Hitch

    #2

    gwdixon

    Elite Member
    Joined
    Jul 31, 2009
    Messages
    2,889
    Location
    Northern CA

      Get a Cat 2 Pat's Easy Change. (click on the blue link) Then bush the pins on the Cat 1 to make them Cat 2.

      This is what I did with a Cat 2 Kubota M7040 and it works great for both categories. I was able to get the slide in replacements. Not sure if they are still made. Give them a call. They are very helpful.

      Pat's is a sponsor on TBN. Check the top of the "Attachments" forum.

      Feb 5, 2014 / Using Category 1 and 2 Equipment With the Same Quick Hitch

      #3

      Tx Jim

      New Member
      Joined
      Jan 26, 2007
      Messages
      10,080
      Location
      Coyote Flats,Tx
      Tractor
      JD 4255/Kubota M7040 HDC

        gwdixon
        I agree on getting Cat 2 Pat's easy change. Only other option would be convert MX 8 to Cat l hitch.
        OSHA will be after you for removing the pto safety shield that's always in the way when attaching/detaching pto coupler.Using Category 1 and 2 Equipment With the Same Quick Hitch (3)

        Feb 5, 2014 / Using Category 1 and 2 Equipment With the Same Quick Hitch

        #4

        bandaidmd

        Platinum Member
        Joined
        Jun 20, 2013
        Messages
        602
        Location
        DelMarVa
        Tractor
        kubota b2620,b8200

          Feb 5, 2014 / Using Category 1 and 2 Equipment With the Same Quick Hitch

          #5

          gwdixon

          Elite Member
          Joined
          Jul 31, 2009
          Messages
          2,889
          Location
          Northern CA

            Another option that I had wished I'd done is to buy the weld-on Pat's Cat 2, cut off the ball ends of the tractor's 3PH, and weld the Pat's in the ball's place. That would keep the extendable feature of the lower lift arm hook-ups.

            I may just do it anyway and sell the current set of Pat's. Trouble is, they were custom made for the dimensions of the M7040. However, they will fit a L5240 since my neighbor bought a set and the measurements were the same.

            Oh, well...decisions, decisions.

            Feb 5, 2014 / Using Category 1 and 2 Equipment With the Same Quick Hitch

            #6

            Gary Fowler

            Super Star Member
            Joined
            Jun 23, 2008
            Messages
            11,917
            Location
            Bismarck Arkansas
            Tractor
            2009 Kubota RTV 900, 2009 Kubota B26 TLB & 2010 model LS P7010

              Without researching the width dimensions to verify if it will work, you may be able to buy a Cat 2 hitch then just swap the pins on the smaller stuff to Cat 2 size. I don't know if putting Cat 1 pins in a heavy bush hog like the MX8 would be safe, but upgrading all the small stuff to larger pins would be a snap. The attachment bolt holes in CAT 1 and 2 are the same diameter, just the pins are larger. First thing I had to do with my tiller was swap out the Cat 1 pins with Cat 2 so they fit my tractors hitch. I don't use a quick hitch so I have no idea if the width is the same. Google the hitch dimensions and you might get a standard dimension, but not all companies follow that to the letter either.

              Feb 5, 2014 / Using Category 1 and 2 Equipment With the Same Quick Hitch

              #7

              Deerherd

              Veteran Member
              Joined
              Apr 9, 2012
              Messages
              1,053
              Location
              Upstate, NY
              Tractor
              LS P7030 CPS, 2016 Bobcat E42, Ferris IS3100z w/37 HP Kawasaki

                I have a Cat 2 QH and converted several implements to fit by getting extended Cat 1 pins and the Cat 1 to Cat 3 QH bushings. You need to use the bushing with raised end or the implement WILL fall off. Things like a spreader work out fine but I would imagine you could tear up a too light box blade on your bigger tractor. Be safe! Here is what I used:

                Feb 5, 2014 / Using Category 1 and 2 Equipment With the Same Quick Hitch

                • Thread Starter

                #8

                OP

                T

                trook

                Gold Member
                Joined
                Oct 21, 2007
                Messages
                455
                Location
                North Central Mississippi
                Tractor
                JD 5075E Cab

                  Deerherd,

                  I thought about that. What about the increased distance from the top hook of the quick hitch versus the top pin of the implement. Are the distances different or is the only difference the distance between the bottom pins?

                  Feb 5, 2014 / Using Category 1 and 2 Equipment With the Same Quick Hitch

                  #9

                  Deerherd

                  Veteran Member
                  Joined
                  Apr 9, 2012
                  Messages
                  1,053
                  Location
                  Upstate, NY
                  Tractor
                  LS P7030 CPS, 2016 Bobcat E42, Ferris IS3100z w/37 HP Kawasaki

                    Only difference is the width of the bottom pins. I have several implements, such as a rake and box blade that are both cat 1 & 2 QH compatible.

                    Edit: I just saw you have a Deere. Not sure if it is different.

                    Feb 5, 2014 / Using Category 1 and 2 Equipment With the Same Quick Hitch

                    #10

                    Tx Jim

                    New Member
                    Joined
                    Jan 26, 2007
                    Messages
                    10,080
                    Location
                    Coyote Flats,Tx
                    Tractor
                    JD 4255/Kubota M7040 HDC

                      gwdixon said:

                      Another option that I had wished I'd done is to buy the weld-on Pat's Cat 2, cut off the ball ends of the tractor's 3PH, and weld the Pat's in the ball's place. That would keep the extendable feature of the lower lift arm hook-ups.
                      Oh, well...decisions, decisions.

                      If you decide to sell the Pats easy change in your photo PM me with the price you want as I'm going to check TODAY with Pat when they open on availability & price. As you can ascertain from my profile I own a M7040.

                      Using Category 1 and 2 Equipment With the Same Quick Hitch (2024)
                      Top Articles
                      Latest Posts
                      Recommended Articles
                      Article information

                      Author: The Hon. Margery Christiansen

                      Last Updated:

                      Views: 5925

                      Rating: 5 / 5 (70 voted)

                      Reviews: 93% of readers found this page helpful

                      Author information

                      Name: The Hon. Margery Christiansen

                      Birthday: 2000-07-07

                      Address: 5050 Breitenberg Knoll, New Robert, MI 45409

                      Phone: +2556892639372

                      Job: Investor Mining Engineer

                      Hobby: Sketching, Cosplaying, Glassblowing, Genealogy, Crocheting, Archery, Skateboarding

                      Introduction: My name is The Hon. Margery Christiansen, I am a bright, adorable, precious, inexpensive, gorgeous, comfortable, happy person who loves writing and wants to share my knowledge and understanding with you.